Car Auto

Phone prewire extension harness (center console on the left side of the fuselage, fig. 1) must be fitted to the E46 (328i 328iA) produces 6/98 in the first two weeks, if the phone is installed. Telephone option prewire, SA640 installed in the vehicles, which are produced in 6/98 in the first two weeks. E46's produced after the second week of 6/98 has this phone, prewire option SA640 is installed at the factory.

Install the harness on the left side of the center console frame on your phone:
1. remove the shifter indicator cover (automatic) or the boot (manual) and remove front fasteners (1).
2. remove the rear ashtray to use two rear brackets (2). Lift up the parking brake in the boot and lift the brake handle.
3. remove the center console (automatic JavaScript).
4. remove the center console for current phone "prewire" connector is available (1)

Download here

Most of the 18 "wheels to clear the outer diameter of the thickness of the 355mm kit. The critical area is the difference between a bicycle spokes and the face of the thickness. Assume that the 19 "20" or even 24 "wheel clears the thickness of the face. The actual distance in front of the wheel spokes in stock of metals within the rotor is in front of the BMW X 5 64.85 mm kit. StopTech recommends a minimum 2 mm more space. Wheel fitment on the drawing page, more precise measurements, www.stoptech.com StopTech website. Note: Final to be fitted to the wheel brake caliper is the responsibility of the customer.

Spread Cuts
Spread the pieces are obtained when the thickness of the product. This will also reduce the size of the bicycle as an extension of the vehicle's track width. Fender clearances must be reviewed to reduce the cars and long lug bolts or the wheel bolts is not usually required. Note: the wheel Industry Council has issued guidelines advising that spread the pieces will not be used. Is to make sure that spread the pieces correctly specified and installed the responsibility of the customer.

Download here

Content:
1. at the bottom of the housing model 80
2. the model 80 vinyl-covered enclosure top
3. Alumapro Alusonic 8 subwoofer (optional)
4. Subwoofer Grille (optional)
5. the Terminal cup
6. the Self-adhesive gasket foam
7. cut the cord
8. (8) # 10 x 3/4 "Phillips pan screws
9. (4) # 10 x 1 "hex head sheet metal screws
10. (4) 1 "basket of tiles
11. (4) 3/8 "thick rubber washers
12. (12) 1/16 "thick rubber washers
13. (4) # 8 x ½ "Phillips head screws
14. (4) # 8 nuts

What you need:
1. Power drill
2. for 5/16 ", 3/16", 7/64 ", 1/8" drill bits
3. Philips screwdriver
4.3/8 "socket driver or wrench
5. Stiff Blade putty knife or similar flat-bladed tool
6. life management saw or hacksaw blade holder & blade

Remove the old enclosure
1. carefully remove the cover on the rear of the subwoofer enclosure lid lifting first, and then raising the size of the cover straight up. The cover should be removed, but it may require extra effort to release the rear. Take your time and be careful when removing the cover, sub-! The easiest way is to add a flat, metal, deals with the tool as a stiff putty knife and carefully pry up the back on each side.
2. remove the mounting screws (2) in the light of the current speaker enclosure (1) 4.
3. remove the old casing (1) by pulling upwards. Disconnect the wiring harness connector (2), and remove the entire casing of the vehicle.
4. using a socket wrench, loosen and remove the brackets (1) that the original plant was connected to the enclosure. The color of the diagonal cutters or a small knife, carefully cut away the plastic saw 4 (2).

Downloadhere

Most of the 17 "wheels to clear the outer diameter thickness of 328 or 332mm rotor Kit. 355 Mm Kit at least 18 "wheel is typically required, and 380 mm rotor Kit, you need at least 19" wheel. The critical difference, however, is the status of the wheel spokes and the face of the thickness. Do not assume that the larger the diameter of the wheel in automatically empties the face thickness.

To determine the actual distance between the surfaces of the metal in the face of the wheel on the inside of the rotor in stock, www.stoptech.com on the home page of the website and click the StopTech "wheel fitment Charts" link. BEFORE YOU print out a copy of the wheel to be mounted on the drawing for your car, click on the "using the charts?"link at the top of the page and read the instructions carefully to ensure that you fully understand how to measure critical wheel clearances. Until then if you click on the link for your vehicle, and print out the relevant wheel fitment on the drawing, use the measurement as a template.

Is very important to check the accuracy of the output of the scale corresponds to the width and length dimensions of the car. StopTech recommends a minimum 2 mm more space to add these dimensions the dimensions is indicated in mm, but in one dimension, for each direction is also displayed in inches. Follow the instructions carefully, to produce the installation in the model and to ensure that the measurements are very accurate.

Download here